放在一個平整干凈的平面上，連接電源和氣源，兩者確認接通之后就開始進行操作。打開氣泵開關，電源總開關，控制臺開關，在控制臺按手動按鈕，然后在顯示屏上找到原點設定，點擊輔助原點設定，然后點擊頭部原點設定，注意原點設定時避免頭部和輔助吸盤碰撞。等設定好然后返回找到玻璃厚度設定，先是玻璃的厚度然后是鋁隔條然后還是玻璃的厚度，輸入完以后，點擊設置進入。
Put it on a flat and clean surface, connect the power supply and air source, and start the operation after they are confirmed to be connected. First turn on the air pump switch, the main power switch and the console switch, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, and then click the head origin setting. Pay attention to avoid collision between the head and the auxiliary suction cup when setting the origin. After setting, go back to find the glass thickness setting, first the glass thickness, then the aluminum spacer, and then the glass thickness. After entering, click the setting to enter.
等命令位置和當前位置數值一致即可，注意設置時傳送帶上不要有玻璃。然后是混交了，按桶膠按鈕，按工作選擇按鈕，然后按拍膠啟動，在按伐開，此時膠頭以出膠，等看不見白膠，以混均勻以后按伐關，在按鏈接生產線，自動，自動運行，此時可以自動打膠。
Wait until the command position is consistent with the current position value. Note that there is no glass on the conveyor belt during setting. Then it is mixed. Press the first bucket of glue button, press the work selection button, and then press the glue shooting button to start. Press the cutting open. At this time, the glue head will release the glue. When the white glue is not visible, press the cutting off after mixing evenly. Press the link production line to run automatically and automatically. At this time, the glue can be applied automatically.

調試的注意事項：
Precautions for commissioning:
1、 在當天機器操作完畢后要把膠管內的膠沖出，防止硬化；如果長時間不實用要注意用煤油清洗膠管和膠槍。
1. After the operation of the machine on the same day, the rubber in the rubber hose shall be washed out to prevent hardening; If it is not practical for a long time, pay attention to cleaning the hose and gun with kerosene.
2、 雙組份打膠機使用的硅酮膠或聚硫膠要注意雜質不能過高，低質量的膠容易堵塞膠管的過濾系統，造成出膠不暢或不均勻。
2. For the silicone glue or polysulfide glue used in the two-component gluing machine, attention shall be paid to that the impurities shall not be too high. The low-quality glue is easy to block the filtering system of the hose, resulting in poor or uneven glue delivery.
3、 在更換膠的品種時要特別注意把雙組份打膠機內殘留的膠沖凈，好清洗，因為不同品種甚的膠容易反應堵塞機器。
3. When changing the type of glue, pay special attention to flush the residual glue in the two-component gluing machine, and it is best to clean it, because the glue of different types and even brands is easy to react and block the machine.
液壓站系統的壓力，不能調的太高，要根據室內環境溫度等實際情況，調滿足膠嘴正常出膠均勻打膠即可。打開液壓站時一定要打開膠槍?zhuān)駝tB組份管路壓力將升得很高，造成事故。
The pressure of the hydraulic station system cannot be adjusted too high. According to the actual situation such as indoor ambient temperature, adjust it to meet the normal glue output of the glue nozzle and apply glue evenly. When opening the hydraulic station, be sure to open the glue gun, otherwise the pressure of component B pipeline will rise very high, resulting in safety accidents.
本文由雙組份打膠機整理發布，您是不是對這些內容有所了解了呢?更多的內容請點擊：http://ruiyingjituan.com我們會(huì )有更多精彩內容等你查看。
This article is compiled and released by two-component gluing machine. Do you know something about these contents? For more information, please click: http://ruiyingjituan.com We will have more wonderful content for you to see.