全自動點膠機膠閥滴漏經常發生于膠閥關畢以后，95%的此種情形是因為使用的針頭口徑太小所致。
The leakage of rubber valve of automatic dispenser often occurs after the valve is closed. 95% of this situation is due to the small diameter of the needle used.
連接氣閥：將點膠控制器的AIR OUT口通過氣管連接到針筒，并把針筒氣閥連接到點膠控制器的AIRIN。
Connect the air valve: connect the air out port of the dispensing controller to the syringe through the air pipe, and connect the needle cylinder air valve to airin of the dispensing controller.
一般利用控制全自動點膠機混合管長度與控制壓桿分別來決定膠水混合程度和控制膠水通斷?；旌瞎艿幕旌戏绞綖殪o態混合，由一連串左右旋葉片相互垂直排列在套管內組成，A、B膠水經過混合管時進行連續的切割與重合為均勻的混合液?；旌瞎艹隹诓靠山愚D接頭，方便使用任何口徑的針頭，以保證出膠量精確。
Generally, the glue mixing degree and glue on-off can be determined by controlling the length of mixing pipe and controlling the pressure bar of automatic dispensing machine. The mixing mode of mixing pipe is static mixing, which is composed of a series of left and right rotating blades arranged vertically in the casing pipe. Glue a and B are continuously cut and overlapped when passing through the mixing pipe to form a uniform mixture. The outlet of the mixing tube can be connected with an adapter, which is convenient to use any diameter needle to ensure the accurate glue output.
針筒放入針筒夾持器后并固定就可以連接氣閥了。將點膠控制器的AIR OUT口通過氣管連接到針筒，并把針筒氣閥連接到點膠控制器的AIRIN。將點膠機的‘點膠’接口通過電纜線連接到點膠控制器的信號輸入接口。腳踏板連接：把腳踏板連接到點膠機的‘運行’接口上，以控制點膠機的運行。Z軸電纜連接：將Z軸的連接電纜插頭與點膠機‘Z軸’連接。

After the needle cylinder is put into the needle holder and fixed, the air valve can be connected. Connect the air out port of the dispensing controller to the syringe through the air pipe, and connect the needle cylinder air valve to airin of the dispensing controller. Connect the "dispensing" interface of dispensing machine to the signal input interface of dispensing controller through cable. Pedal connection: connect the foot pedal to the "running" interface of the dispenser to control the operation of the dispenser. Z-axis cable connection: connect the z-axis cable plug with the "z-axis" of the dispenser.
太小的針頭會(huì )影響液體的流動造成背壓， 結果導致膠閥關畢后不久形成滴漏的現象。過小的針頭也會(huì )影響膠閥開始使用時的排氣泡動作，只要更換較大的針頭即可這種問題。
If the needle is too small, it will affect the flow of liquid and cause back pressure. As a result, the phenomenon of drip will be formed soon after the rubber valve is closed. If the needle is too small, it will affect the exhaust bubble action when the rubber valve starts to use. As long as the larger needle is replaced, this problem can be solved.
錐形斜式針頭產生的背壓少，液體流動順暢。
The conical oblique needle produces the least back pressure and the most smooth liquid flow.
液體內空氣在膠閥關畢后會(huì )產生滴漏現象, 好是預先排除液體內空氣, 或改用不容易含氣泡的膠.或先將膠離心脫泡后在使用.瞬間膠( 快干膠 ) 在膠閥接頭及管路上堵塞此種情形主要因過多的濕氣或重復使用過的瞬間膠. 應確保使用新鮮的瞬間膠. 將管路以未含濕氣的Aceton丙酮徹底清洗過. 使用的空氣應確定完干燥且于廠內空壓與膠閥系統間加裝過濾器. ( 以上方法如仍然無效, 則應使用氮氣. )
The air in the liquid will leak after the rubber valve is closed. It is better to remove the air in the liquid in advance, In this case, it is mainly due to excessive moisture or repeated use of instant glue. Make sure to use fresh instant glue. Clean the pipeline thoroughly with aceton acetone without moisture The air used should be dried and a filter should be installed between the air pressure system and the rubber valve system in the plant. (if the above method still fails, nitrogen should be used.)
需要注意的是，將手持式編程器通過串口線選擇到點膠機左側的接口上。6.如所用點膠控制器同點膠機的連接器型號相同，可以根據連接器的芯數不同來看出點膠機的‘點膠’和‘運行’等連接口，二芯點膠，三芯運行。
It should be noted that the handheld programmer is selected to the interface on the left side of the dispenser through the serial port line. 6. If the type of the dispenser connector used is the same as that of the dispenser, the "dispensing" and "running" interfaces of the dispenser can be seen according to the number of cores of the connector, two core dispensing and three core operation.