點膠設備哪些因素會(huì )影響出膠點膠質量?
時間:2019-10-07 來源:http://ruiyingjituan.com/ 發布人:昌盛機械
點膠機自動自動點膠設備在使用過程中有那那些因素會(huì )影響到出膠點膠的質量?雙組份打膠機小編今天為大家講解一下;
What factors will affect the quality of the dispensing machine during the use of automatic dispensing equipment? The small edition of two-component glue beater will explain it to you today.
影響出膠點膠量的設備、環境及膠液的相關因素如下:
The equipment, environment and the related factors affecting the amount of glue produced are as follows:
1.自動點膠設備出膠針頭大小,在工作實際中,針頭內徑大小應為點膠膠點直徑的1/2左右,點膠過程中,應根據產品大小來選取點膠針頭。大小相差懸殊的產品要選取不同針頭,這樣既可以保證膠點質量,又可以提高生產效率。
1. The size of dispensing needle of automatic dispensing equipment should be about 1/2 of the diameter of dispensing point in actual work. In dispensing process, the size of dispensing needle should be selected according to the size of product. Different needles should be selected for products with different sizes, which can not only ensure the quality of adhesive point, but also improve the production efficiency.
2.自動點膠設備的壓力設定,點膠設備給針管或膠提供一定壓力以保證膠水供應,壓力大小決定供膠量和膠水流出速度。壓力太大易造成膠水溢出、膠量過多;壓力太小則會(huì )出現點膠斷續現象和漏點,從而導致產品缺陷。應根據膠水性質、工作環境溫度來選擇壓力。環境溫度高會(huì )使膠水粘度變小、流動性變好,這時需調低壓力值,反之亦然。
2. Pressure setting of automatic dispensing equipment, dispensing equipment provides a certain pressure to needle tube or glue to ensure glue supply. Pressure determines the amount of glue supply and the speed of glue flow. Excessive pressure can easily cause glue overflow and excessive glue content; too low pressure can cause intermittent dispensing and leakage, resulting in product defects. Pressure should be selected according to the properties of glue and working environment temperature. High ambient temperature will make the glue viscosity smaller and fluidity better. At this time, low pressure should be adjusted, and vice versa.
3.自動點膠設備出膠時間的設定,根據工作經驗,膠點直徑的大小應為產品間距的一半。這樣就可以保證有充足的膠水來粘結組件又避免膠水過多。點膠量多少由自動自動點膠設備設置的時間長短來決定,實際中應根據生產情況(室溫、膠水的粘性等)選擇點膠設定時間。
3. Setting the dispensing time of automatic dispensing equipment. According to the working experience, the diameter of the dispensing point should be half of the product spacing. This ensures that there is sufficient glue to bond components and avoid excessive glue. The amount of dispensing is determined by the setting time of automatic dispensing equipment. In practice, the setting time of dispensing should be selected according to the production conditions (room temperature, glue stickiness, etc.
- STJ03B型雙組份打膠機的性能和結構特點 2024/07/13
- 全自動鋁條折彎機鋁框自動打標技術 2024/07/11
- 中空玻璃打膠的好壞與哪些方面有關系? 2024/07/09
- 中空玻璃生產線和復合膠條中空玻璃生產線區別? 2024/07/04
- 中空玻璃加工設備故障分析流程 2024/07/03
- 中空玻璃加工設備的現場安裝事項要點 2024/06/27
- 中空玻璃的生產過程是怎樣的? 2024/06/24
- 中空玻璃生產線的構造及功能介紹 2024/06/19
- 中空玻璃生產線有哪些設備組成 2024/06/13
- 丁基涂布機的膠嘴漏膠會(huì )不會(huì )營銷生產質量? 2024/06/13
產品分類Product categories
聯系我們Contact us
- 咨詢熱線:0531-85717458 13705446998
- 公司地址: 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們: