前兩天有客戶問小編，中空玻璃全自動打膠機出黑膠但是沒有壓力是怎么回事。小編看見之后迅速和提問者取得聯系，幫助他了這個問題。小編想到還有很多人不知道這些問題的辦法，就和大家也說說辦法。
Two days ago, a customer asked Xiaobian, hollow glass automatic gluing machine out of black glue, but no pressure is how it is. Xiaobian quickly contacted the questioner and helped him solve the problem. Xiaobian thought that there were many people who did not know the solution to these problems, so he told everyone about the solution.
要檢查一下打膠機的氣源區間在不在0.6~0.8Mpa之間。這個如果沒在調好之后再試一下。如果本來就在這個區間，進行下一個步驟：
First, check that the air source of the glue beater is between 0.6 and 0.8 Mpa. If it's not ready, try again. If it's already in this area, take the next step:
看看觸屏中編輯功能菜單中的密封不使用選項是否打開；
See if the sealing option in the editing menu on the touch screen is turned on.
檢查開關，氣動開關是否阻塞；檢查黑膠氣動開關與電磁閥動作是否正常；
Check the switch, whether the pneumatic switch is blocked; check whether the black rubber pneumatic switch and solenoid valve operate normally;
檢查一下中空玻璃自動打膠機比例泵上的智能壓力表是否處在正常范圍，7~35Mpa。
Check whether the intelligent pressure gauge on the proportional pump of the hollow glass automatic gluing machine is in the normal range, 7-35 Mpa.

檢查打膠機上的液壓站是否有壓力，如果沒有壓力的話：（1）清洗比例溢流閥。（2）檢查比例控制器是否正常通電又或者稍微松動。
Check whether there is pressure in the hydraulic station of the glue beater, if there is no pressure: (1) Clean the proportional relief valve. (2) Check whether the proportional controller is normally powered on or slightly loosened.
檢查一組比例泵下限傳感器是否有信號，檢查二組比例泵是否有信號，后檢查一下掃描儀數值是否正常。
Check whether the lower limit sensor of a group of proportional pumps has a signal, check whether the two groups of proportional pumps have a signal, and finally check whether the scanner value is normal.
經過這幾個步驟，打膠機沒有壓力的問題應該就可以很好的得到！
After these steps, the glue machine without pressure should be able to solve the problem very well!
今天給大家介紹的內容就到這里了，相信以上的介紹能給大家帶來一定的幫助，如果您對文章的內容還有不明白的地方，歡迎大家到全自動打膠機的網站留言討論：http://ruiyingjituan.com
This is the end of today's introduction. I believe that the above introduction can bring you some help. If you still don't understand the content of this article, you are welcome to leave a message on the official website of the automatic gluing machine for discussion: http://ruiyingjituan.com.