在使用過程中雙組份打膠機的事項有哪些?
時間:2021-03-30 來源:http://ruiyingjituan.com/ 發布人:昌盛機械
雙組份涂膠機是生產中空、幕墻玻璃的專用設備,可一次完成二道密封中A、B組份混合與涂膠。適用配比精度高的膠種,滿足玻璃深加工企業率、高合格率流水線作業的生產需求,是大規模生產高檔中空玻璃及玻璃幕墻產品的一種理想的配套設備。
The two-component gluing machine is a special equipment for the production of hollow and curtain wall glass, which can complete the mixing and gluing of a and B components in two seals at one time. It is an ideal equipment for large-scale production of high-quality insulating glass and glass curtain wall products.
1.由于雙組份密封膠的固化需要一定時間,因此,已涂了雙組份密封膠的玻璃應水平輕輕搬動。
1. As the curing of two-component sealant takes a certain time, the glass coated with two-component sealant should be moved horizontally and gently.
2.A組、B組份膠應保持清潔,嚴防異物進入膠中。
2. The glue of group A and group B should be kept clean to prevent foreign matters from entering the glue.
3.在連續工作過程中,膠槍每次停止工作時間一般不得超過20分鐘,否則,應用A組份膠沖出全部混合膠,直單一的A組份膠從槍口排出為止。
3. In the process of continuous operation, the stopping time of the glue gun shall not exceed 20 minutes, otherwise, all the mixed glue shall be washed out with component a glue until the single component a glue is discharged from the muzzle of the gun.
4.高壓膠管不得強行擠壓、彎曲,防止影響系統正常工作。
4. The high pressure hose shall not be forced to squeeze or bend to prevent affecting the normal operation of the system.
5.混膠器應經常保持暢通,以保證良好的出膠效果。如遇堵塞情況,可用丙酮浸泡后清洗。建議每5組清洗一次。
5. The mixer should always be kept smooth to ensure a good glue out effect. In case of blockage, it can be cleaned after soaking in acetone. It is recommended to clean every 5 groups.
6.當膠槍長時間不用時(超過一周),應拆下槍體使用溶劑將膠槍和混膠器內的殘留膠體清洗干凈。
6. When the glue gun is not used for a long time (more than one week), the gun body should be removed and the residual colloid in the glue gun and mixer should be cleaned with solvent.
7.不同雙組份膠生產廠家所生產的膠內含雜質數量不同,根據實際情況清晰B組分的過濾網及單向止回閥,建議每?jì)山M清洗一次。
7. The amount of impurities in the glue produced by different two-component glue manufacturers is different. According to the actual situation, it is recommended to clean the filter screen and one-way check valve of component B every two groups.
8.任何因膠體固化所造成的膠槍、管路或整機的故障,一律不在保修范圍之內。
8. Any failure of glue gun, pipeline or whole machine caused by glue solidification is not within the scope of warranty.
9.定期給各泵的加油口加油,應保證油霧器內不斷油。
9. Add oil to the oil inlet of each pump regularly to ensure continuous oil in the oil mist device.
- STJ03B型雙組份打膠機的性能和結構特點 2024/07/13
- 全自動鋁條折彎機鋁框自動打標技術 2024/07/11
- 中空玻璃打膠的好壞與哪些方面有關系? 2024/07/09
- 中空玻璃生產線和復合膠條中空玻璃生產線區別? 2024/07/04
- 中空玻璃加工設備故障分析流程 2024/07/03
- 中空玻璃加工設備的現場安裝事項要點 2024/06/27
- 中空玻璃的生產過程是怎樣的? 2024/06/24
- 中空玻璃生產線的構造及功能介紹 2024/06/19
- 中空玻璃生產線有哪些設備組成 2024/06/13
- 丁基涂布機的膠嘴漏膠會(huì )不會(huì )營銷生產質量? 2024/06/13
產品分類Product categories
聯系我們Contact us
- 咨詢熱線:0531-85717458 13705446998
- 公司地址: 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們: